Canon CXDI-801C Wireless

Wireless Digital Radiography System

Designed to work in small places, the CXDI-801C DR System is designed for use in a variety of diagnostic imaging areas and radiology rooms where it helps to provide convenience and time savings.  This system is the ideal size for fitting into most wall stands, buckeys, mobiles, and incubators without modification.


High Resolution and High Sensitivity

With a 125 micron pixel pitch, the CXDI-801C Wireless Digital Radiography (DR) System delivers exceptional spatial resolution. The high sensitivity of the Cesium Iodide (CsI) scintillator helps reduce the X-ray exposure to the patient. The maximum 3 second exposure time allows this digital detector to be used with tomography equipment and for other exams that may require an exposure time of up to 3 seconds.

Portable and Flexible

The CXDI-801C Wireless DR System may be used in multiple x-ray rooms. Simply “check in” the digital detector in the computer. The Infrared (IR) Communication module makes it easy to switch detectors among the systems. For easy transport, an optional handle is available.

Wireless Range

The wireless communication may be set for applicable strength, and, depending on the room where the CXDI-801C Wireless DR System is used, the power can be managed. Should the wireless connection be lost, the unit will automatically attempt to reconnect and to prevent image loss. Acquired images are stored locally in the on-board memory. Once reconnected, the images can be retrieved. An optional wiring unit allows images to be transferred from a panel mounted in a Bucky tray to the control computer over hard wire.

5 GHz for Fast Data Transfer

The CXDI-801C Wireless DR Detector runs at 5 GHz and 2.4 GHz on an 802.11n network that increases signal clarity – resulting in fast data transfer speed.


The battery lasts approximately 6.5 hours and takes less than 3 hours to charge. The battery can be charged in the unit with the wired option (sold separately). An accessory battery charger (sold separately) can additionally charge up to 2 batteries at a time so a fresh battery can be continuously available. The control console includes a battery indicator for image count and power level monitoring. Additional batteries (sold separately) are also available.

CXDI Control Software NE

The CXDI-801C Wireless DR System uses the Canon CXDI Control Software NE. The software gives a wide range of selections and images can be taken with three touches. An on-screen preview image is available approximately 1-2 seconds after exposure. The image processing shows subtle details of trabecular bone structure and soft tissue in the same image.

Method Cassette Size Detector, Scintillator & Amorphous Silicon (a-Si)
Scintillator Csl (Csl: TI)
Sensor LANMIT (Large Area New-MIS sensor and TFT)
Pixel Pitch 125 Microns
Pixels 2,192 x 2,800 Pixels (6.1 Megapixels)
Imaging Area Approximately 11 x 14 in (27.4 x 35 cm)
Standard Configuration Sensor Unit, X-Ray Interface Box (optional), Battery Charger, Detector Check-In Unit, Wireless Access Point (Including A/C Power)
Recharge Time Less Than 3 Hours
Performance Approximately 140 Images
Image Acquisition and Processing
Image Processing Standard Advanced Multi-Frequency Processing
A/D 16-bit
Grayscale Output 12 bit or 16 bit Selectable
Preview Image Approximately 1-2 Seconds After X-ray Exposure
Full Image Display Approximately 5-6 Seconds After X-ray Exposure
Data Output and Network Connection
Wireless Standard IEEE 802.11n (5 & 2.4 GHz)
DICOM DICOM 3.0 Compatible, Print Management (SCU), Storage (SCU), MWL (SCU), MPPS (SCU)
Electrical and Environmental
Operating Environment Sensor unit: 41-95°F (5-35°C), Humidity 30-80% RH (non-condensing)
Physical Characteristics
Dimensions (W x L x H) 12.1 x 15.1 x 0.6 in (307 x 384 x 15 mm)
(Detector unit only)
Weight 5.1 lbs (2.3 kg) (with battery)
Specifications are subject to change without notice.